The lightning flash with arrowhead
symbol, within an equilateral triangle is
intended to alert the user to the presence
of uninsulated “dangerous voltage”
within the product’s enclosure that may
be of sufficient magnitude to constitute a
risk of electric shock to persons.
CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature
To reduce the risk of electric shock. Do
not remove cover (or back). No user
serviceable parts inside. Refer servicing
to qualified service personnel.
CAUTION:
accompanying the appliance.
DT-V9L1D
INSTRUCTIONS
Table of Contents
Safety Precautions .............................................. 2
IMPORTANT SAFEGUARDS ........................... 2
Maintenance..................................................... 3
MULTI FORMAT LCD MONITOR
Installation............................................................ 4
To adjust the stand height ................................ 4
Daily Operations / Connections ......................... 6
Front panel ....................................................... 6
Rear panel........................................................ 8
Available signals............................................... 9
Menu Configuration—MAIN MENU .................. 10
Menu Configuration—SET-UP MENU............... 12
External Control................................................. 14
About the external control .............................. 14
Using the MAKE/TRIGGER system ............... 14
Using the RS-232C system............................ 15
Troubleshooting................................................. 16
Self-check program ........................................ 16
Specifications .................................................... 17
General........................................................... 17
Input/output terminals..................................... 17
Dimensions..................................................... 18
ENGLISH
U.S.A. only
European Union only
FCC NOTICE
EMC Supplement
CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the
equipment.
This equipment is in conformity with the provisions and protection requirements of the corresponding
European Directives. This equipment is designed for professional video appliances and can be used in the
following environments:
• Controlled EMC environment (for example purpose built broadcasting or recording studio), and rural
outdoors environment (far away from railways, transmitters, overhead power lines, etc.)
In order to keep the best performance and ensure electromagnetic compatibility, we recommend to use cables
not exceeding the following length:
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Cable
Power cord
Video signal cable
Audio signal cable
RS-232C cable
Length
2.0 m
2.0 m
1.5 m
2.0 m
(attached cable (H05VV-F 3 x 0.75 mm2))
(coaxial cable)
(shielded cable)
IMPORTANT RECYCLING INFORMATION
This product has a fluorescent lamp that contains mercury. Disposal of these materials
may be regulated in your community due to environmental considerations. For disposal
or recycling information, please contact your local authorities or for USA, the Electronic
(shielded cable)
(A straight cable with a D-sub 9-pin connector)
REMOTE cable
(twist pair cable)
2.0 m
(A straight LAN cable)
The inrush current of this apparatus is 6.269 ampere.
European Union only
CAUTION
Dear Customer,
In case where the strong electromagnetic waves or magnetism are near the audio cable or the signal cable,
the sound or the picture will contain noise. In such cases, please keep the cable away from the sources of the
disturbance.
This apparatus is in conformance with the valid European directives and standards regarding electromagnetic
compatibility and electrical safety.
European representative of Victor Company of Japan, Limited is:
JVC Technology Centre Europe GmbH
Postfach 10 05 52
61145 Friedberg
Maintenance
Unplug this product from the wall outlet before
Cabinet
cleaning.
Germany
To avoid the deterioration or damages of the cabinet
such as its paint’s peeling away, be careful about the
following:
• Do not wipe the cabinet using solvent such as
alcohol, thinner, or benzine.
• Do not expose the cabinet to any volatile substance
such as insecticides.
• Do not allow any rubber or plastic in contact for a
long time.
Screen
Information for Users on Disposal of Old Equipment
[European Union]
To avoid irreparable change in appearance of the
screen such as uneven color, discoloration, scratches,
be careful about the following:
This symbol indicates that the electrical and electronic equipment should not be disposed
as general household waste at its end-of-life. Instead, the product should be handed over
to the applicable collection point for the recycling of electrical and electronic equipment for
proper treatment, recovery and recycling in accordance with your national legislation.
• Do not paste or stick anything using any glues or
adhesive tapes.
• Do not write anything on the screen.
• Do not strike the screen with a hard object.
• Avoid condensation on the screen.
• Do not wipe the screen with solvent such as alcohol,
thinner, or benzine.
• Do not wipe the cabinet forcefully.
By disposing of this product correctly, you will help to conserve natural resources and will
help prevent potential negative effects on the environment and human health which could
otherwise be caused by inappropriate waste handling of this product. For more information
about collection point and recycling of this product, please contact your local municipal
office, your household waste disposal service or the shop where you purchased the
product.
Wipe stains off the cabinet with a soft cloth. If the
cabinet gets heavily stained, wipe it with a soft cloth
soaked in water-diluted neutral detergent and wrung
well, then wipe with a soft dry cloth.
Attention:
• Do not wipe the screen forcefully.
This symbol is
only valid in the
European Union.
If the screen gets stained, wipe it with a soft dry cloth,
a soft damp cloth, or a soft cloth soaked in water-
diluted neutral detergent and wrung well.
Ventilation openings
Penalties may be applicable for incorrect disposal of this waste, in accordance with
national legislation.
Use a vacuum cleaner to get rid of the dust around the
intakes (all the openings). If a vacuum cleaner is not
available, use a cloth and wipe it off. Leaving the dust
around the intakes may prevent proper temperature
control and cause damage to the product.
(Business users)
obtain information about the take-back of the product.
[Other Countries outside the European Union]
If you wish to dispose of this product, please do so in accordance with applicable national
legislation or other rules in your country for the treatment of old electrical and electronic
equipment.
ENGLISH
3
4
Installation
• Do not rest your arm on the monitor or lean against the monitor.
• Do not touch the LCD panel when installing the monitor.
• Make sure to install the monitor securely to prevent the monitor from falling over, which causes damage to the monitor
or injury.
CAUTION
Higher position
When shipped from factory, the stand is attached to the monitor.
You can tilt the monitor from about 20° upward to about 10° downward.
Monitor
Stand
• When the monitor is not
tilted (0°), the guidelines
align as illustrated.
About 20°
0°
Guidelines
About 10°
CAUTION
• Be careful not to pinch your fingers in the gap between the monitor and the stand.
• When the stand is attached to the lower position (☞ page 5), you cannot tilt the monitor downward.
Attachment screws
7 To adjust the stand height
You can select the stand height according to your preference—higher position or lower position.
To change the stand height, change the position of the screw hole used for attaching the stand.
• When shipped from factory, the stand is attached to the higher position.
• Before adjusting the stand height, set the monitor angle to 0°.
CAUTION
• Lay the monitor on a cloth with the LCD panel facing down to prevent the LCD panel from being damaged.
• Depending on the type of external batteries, the stand cannot be attached or detached when the external battery is
attached on the monitor.
• When the stand is attached on the lower position, some types of external batteries cannot be attached to the monitor.
Guide holes (only for attaching
to the higher position)
Screw holes for lower position
Rear panel of the monitor
Screw holes for higher position
Lower position
To prevent an accidental fall
Fix the monitor to a wall by using strings.
Fixing the monitor
Attachment screws
Attach the hook (not provided) to the VESA mounting holes on the rear panel (use the two 100 mm pitch holes
on the upper side) using M4 x 10 mm screws (not provided). Bind the hooks on the rear panel of the monitor to a
wall or a pillar using durable string.
Stand
Monitor
Hook (not provided)
Hook and screws (M4 x 10 mm)
(not provided)
ENGLISH
5
6
Daily Operations / Connections
7 Front panel
• “NO EFFECT” is displayed when you press a button which is not available for the current input or signal format (the lamp
lights even when the function does not actually work).
• The items controlled by the MAKE system cannot be controlled by the buttons on the front panel (“REMOTE ON” is
displayed and the lamps do not light).
8 A. MARKER button/lamp
r FOCUS button/lamp
Displays/hides the area marker.
Helps to focus the picture.
• When the FOCUS lamp lights:
– “PICTURE IMPROVEMENT” is not displayed on
• Select the style of the area marker in “AREA
MARKER” of the MAIN MENU (☞ page 10).
• This function works when the picture is displayed
in 16:9 aspect ratio.
• This function does not work when “MARKER
SELECT” or “R-MARKER SELECT” is set to
“OFF” (☞ “AREA MARKER” in the MAIN MENU
on page 10).
the menu.
– The settings of “PICTURE IMPROVEMENT”
are ineffective.
(☞ page 10)
1 Tally lamp
5 MUTING button
This lamp is controlled by the tally function of the
MAKE/TRIGGER terminal (☞ “TALLY SELECT” in
“FUNCTION SETTING” on page 12 and “External
Control” on page 14).
Turns off the sound when a menu screen is not
displayed.
• To cancel the function, press the button again or
press VOL. +/– buttons.
t DYNAMIC button/lamp
Adjusts the picture to be suitable for a light place.
• When the DYNAMIC lamp lights:
– “BACK LIGHT” and “PICTURE SUB ADJ.” are
not displayed on the menu.
– The setting of “BACK LIGHT” is ineffective.
(☞ page 10, 12)
• This lamp can also be used as the format
indicator (☞ “FORMAT INDICATOR” in
“FUNCTION SETTING” on page 12).
9 S. MARKER button/lamp
6
/
/ / buttons
Displays/hides the safety marker.
When a menu screen is displayed
Selects or adjusts menu items.
☞ “Menu Operations” on page 7
When no menu screen is displayed
• Adjust the area of the safety marker in “AREA
MARKER” of the MAIN MENU (☞ page 10).
• This function does not work when “SAFETY
MARKER” or “R-SAFETY MARKER” is set to
“OFF” (☞ “AREA MARKER” in the MAIN MENU
on page 10).
\
2 Screw holes for attaching protective filter
(provided)
• Attach the protective filter by using the provided
screws.
\
Selects the audio channels of EMBEDDED
AUDIO signals.
y SDI button/lamp
Selects the E. AUDIO HD/SD SDI terminal as a
signal input.
• Attach the filter to the LCD panel with the frosted
side of the filter facing outwards (when shipped
from the factory, a protective film and a sticker are
attached to the frosted side).
☞ “Audio Channel Selection” on page 7
• Pressing button while holding button displays p Power lamp
the SET-UP MENU.
☞ “Menu Operations” on page 7
u VIDEO/COMPO. button/lamp
Selects the VIDEO/COMPONENT terminal as a
signal input.
Unlit: The monitor is completely off (both the
POWER and DC switch on the rear panel are
turned off).
Lights in green: The monitor is on.
Lights in orange: The monitor is off (on standby).
Flashes in orange: The monitor is in the P. SAVE
(power save) mode (☞ “NO SYNC ACTION” in
“SYNC FUNCTION” on 11 page).
CAUTION
7 SCR. CHK. (Screens check) button/lamp
Displays only the selected element (R, G, B, or the
luminance) of video signal.
• Select an appropriate setting of “VIDEO/COMPO.
SEL.” (☞ page 10).
• Use only the provided screws to avoid damaging the
monitor.
• When attaching the protective filter, do not fasten
screws too tightly; otherwise, the protective filter may
be damaged.
i DC lamp
• Each time you press this button, the screen
changes in the following order.
When the DC 12 V power voltage is being lowered
due to the battery consumption, the lamp changes
to orange from green. When the voltage becomes
lower than a certain level, the monitor automatically
turns off and the lamp turns to red.
• Make sure to turn off the DC switch on the rear
panel before replacing the battery.
• The length of time that the lamp lights in orange
differs depending on the type of battery or the
battery condition. It is recommended to replace
the battery when the lamp turns to orange.
Normal screen
Monochrome screen
3 Speaker (monaural)
q
button
The speaker emits audio signals from the AUDIO
(IN) terminal or EMBEDDED AUDIO signals from
the E. AUDIO HD/SD SDI (IN) terminal.
Turns on and off (on standby) the monitor.
• The power switches (POWER and DC) are
equipped on the rear panel of the monitor (☞ 1,
3 on page 8).
Blue screen Green screen
Red screen
4 Picture adjustment knob
PHASE: Adjusts the picture hue. (NTSC only)
CHROMA: Adjusts the picture color density.
BRIGHT: Adjusts the picture brightness.
CONTRAST: Adjusts the picture contrast.
w VOL. +/– buttons
Adjusts the volume.
e MENU button
Displays the MAIN MENU.
☞ “Menu Operations” on page 7
Menu Operations
Audio Channel Selection
About the Information Display
About the Status Display
Select the audio channels when the SDI is
selected as a signal input and EMBEDDED
AUDIO signals come in.
• You have to choose a group of selectable audio
channels before the channel selection (☞
“E.AUDIO GROUP” in “AUDIO SETTING” on
page 11).
The monitor displays the information below
depending on the settings of the menu and
buttons.
If you press the input button of the current input,
the status of the input signal and setting of muting
are displayed for about 3 seconds.
• When “STATUS DISPLAY” is set to “AUTO” or
“ON,” the status below is also displayed in the
following cases (☞ “INFORMATION” on page
13):
1 Display the menu.
To display the MAIN MENU
\
Press MENU button.
To display the SET-UP MENU
\
Press button while pressing button.
MAIN MENU
– When you change the input
– When the signal condition of the current input
changes
1 Press or button when a menu
1 Audio level meter
is not displayed.
• Not displayed when no signal comes in for
the SDI input or “LEVEL METER ch” is set to
“OFF.”
– When you turn on the monitor
The screen for audio channel selection is
displayed.
• The screen for audio channel selection
automatically disappears in about 5 seconds
after the previous operation.
Selected item
Operation guide
☞ “AUDIO SETTING” and “NOTE” on page 11
SET-UP MENU
2 Signal format
• “NO SYNC” is displayed when no video
signal comes in.
• “Out of range” is displayed for a noncompliant
video signal input.
Audio channel selection screen
Selected item
1 Signal format
• “NO SYNC” is displayed when no video
signal comes in.
• “Out of range” is displayed for a noncompliant
video signal input.
• When “COLOR SYSTEM” is set to “AUTO”
and the noncompliant composite video
signals come in, “OTHERS” is displayed (☞
“FUNCTION SETTING” on page 12).
• When “COLOR SYSTEM” is set to “AUTO”
and the noncompliant composite video
signals come in, “OTHERS” is displayed (☞
“FUNCTION SETTING” on page 12).
• Not displayed when “OFF” or “AUTO” is
selected for “STATUS DISPLAY” (☞ page 13).
:
15
Operation guide
2 Press
buttons to select an
2 Press
buttons to select an item,
then press button.
audio channel.
• Each time you press the button, the audio
channel changes according to the settings of
“E.AUDIO GROUP” (☞ “NOTE” on page 11).
3 Source name assigned in “CHARACTER
SET.”
For some items, adjustments will be made by
pressing
.
2 Setting of “VIDEO/COMPO. SEL.”
☞ page 10
• Displayed when “SOURCE ID” is set to “ON.”
• Displayed in large letters when “STATUS
DISPLAY” is set to “OFF” or “AUTO.”
☞ “INFORMATION” on page 13
3 Press MENU button.
The screen for audio channel selection
disappears.
3 Setting of “MUTING”
☞ “5 MUTING button” on page 6
• Displayed only when muting is activated.
Ex.: When “AREA MARKER” in the
MAIN MENU is selected
3 Press
buttons to select an item,
then press
buttons to make
adjustments.
4 Press MENU button to return to the
previous menu.
Pressing the button again finishes the menu
operation.
ENGLISH
7
8
Daily Operations / Connections (cont.)
7 Rear panel
Note for connections
• Before making any connections, turn off all the equipment.
• Use a cord whose plugs correctly match the terminals on this monitor
and the equipment.
• Plugs should be firmly inserted; poor connections could cause noise.
• When unplugging a cord, be sure to grasp its plug and pull it out.
• DO NOT connect the power cord until all connections are completed.
• Refer also to the user manual of each piece of equipment.
CAUTION
Do not connect the power cord until all other
connections are completed.
4 DC IN 12V terminal
6 AUDIO terminal (pin jack)
q Screw holes for external battery attachment
DC 12 V (maximum
DC 17 V) power input
connector.
IN: Input terminal for the analog audio signals.
• Use this terminal for the analog audio connection
of the SDI.
OUT: Output terminal for the analog audio signals
to the AUDIO IN terminal.
Attach external battery for DC 12 V power supply
by using 2 screw holes. Choose the appropriate
screw holes from 1, 2, 3 or 4, according to the type
of external battery.
• Use the Anton Bauer Dionic 90 (mount: QR DXC-
M3A) external battery.
1 POWER switch
Turns the AC power on or off.
• You need to press
panel to turn on the monitor after turning on the
POWER switch.
button on the front
When using DC 12 V power (maximum DC
17 V), check the DC IN 12V terminal pin signal,
and use the correct polarity. If the polarity is
reversed, this could cause a fire or personal
injury.
7 E. AUDIO HD/SD SDI terminal (BNC)
IN: Input terminal for the HD/SD SDI signals.
• The terminals accept also EMBEDDED AUDIO
signals* including up to 12 audio channels with
the sampling frequency of 48 kHz.
CAUTION
2 AC IN terminal
• Do not use the external battery for DC 24 V power
supply.
• Use only the battery specified above. If a heavy
battery is used, it may fall off depending on the way
the monitor is used.
AC power input connector.
• Connect the provided AC power cord to an AC
outlet.
• Attach the provided power cord holder to prevent
accidental disconnection of the AC power cord (☞
page 9).
OUT: Output terminal for the HD/SD SDI signals.
• The signals are re-clocked, then emitted from this
terminal.
• The signals are emitted only when the monitor is
on or in P.SAVE (power save) mode.
• While using both the AC and DC 12 V power
supply, AC power supply is preferentially used. If
the AC power supply is cut off (for example, when
unplugging the AC power cord), the power supply
automatically switches to the DC 12 V power
supply.
* Using the audio level meter
You can check the conditions of the current
EMBEDDED AUDIO signals in the audio level meter.
The setting for the level meter is selected in “AUDIO
SETTING” (☞ page 11).
3 DC switch
Turns the DC 12 V power on or off.
• You need to press
8 REMOTE terminal
button on the front panel
Terminal for controlling the monitor by an external
control.
☞ “External Control” on page 14
to turn on the monitor after turning on the DC
switch.
• The monitor consumes the battery even while the
monitor is on standby. To save battery life, turn off
the DC switch.
5 VIDEO/COMPONENT terminals (BNC)
IN: Input terminals for the composite (VBS) and the
analog component (Y/PB/PR) signals.
• Select the signal type in “VIDEO/COMPO. SEL.”
corresponding to the type of the input signal (☞
page 10).
9 Carry handle
Use this handle when carrying the monitor.
p Security slot
Install a security wire to this slot.
OUT: Output terminal for the composite (VBS) and
the analog component (Y) signals.
7 Available signals
Attaching the Power Cord Holder
Input terminal
VIDEO/COMPONENT
Signal format shown
in the status display
CAUTION
No.
Signal name
E. AUDIO HD/
SD SDI*1
Depending on the type of external batteries, the cover may not be attached to the case.
VBS
(Composite)
Y/PB/PR
(Analog component)
(☞ page 7)
• The provided power cord holder prevents accidental disconnection of the AC power cord from the AC IN
terminal.
• The power cord holder consists of two parts, a case and a cover.
1
2
3
4
5
6
7
8
9
NTSC*2
NTSC
√
—
—
—
—
√
—
—
—
—
√
PAL
PAL
√
B/W50
NTSC
√
B/W60*2
480/59.94i*2
576/50i
PAL
√
1
2
3
480/60i
576/50i
480/60p
576/50p
720/60p
720/60p
720/50p
1080/60i
1080/60i
1080/60i
1080/60i
1080/50i
1080/60i
1080/50i
1080/60i
1080/24psf
1080/24psf
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
AC IN terminal
√
√
480/59.94p
576/50p
720/60p
√
—
—
√
Case
√
√
CAUTION
Use only the provided screws.
CAUTION
10 720/59.94p
11 720/50p
√
√
Make sure the plug will not be pulled out after the
cover is attached to the case.
√
√
12 1080/60i
√
√
Cover
13 1080/59.94i
14 1035/60i
√
√
• To detach the cover, release the tab.
Tab
√*3
√*4
√
√*3
√*5
√
√*3
√*4
√
√*3
√*5
√
15 1035/59.94i
16 1080/50i
17 1080/30psF
18 1080/25psF
19 1080/29.97psF
20 1080/24psF
21 1080/23.97psF
√
√
√
√
√: Acceptable
—: Not acceptable
*1 Compatible with EMBEDDED AUDIO signals
*2 When the number of vertical scanning lines of the incoming signal is 483, the picture is displayed with 480 lines.
*3 The signal is recognized as 1080/60i.
*4 The signal is recognized as 1080/59.94i.
*5 The signal is recognized as 1080/50i.
• Analog component signals are compatible with Y on sync signals.
ENGLISH
9
10
Menu Configuration—MAIN MENU
For the operation procedure, see page 7.
PICTURE IMPROVEMENT
Setting for the picture quality
Item
APERTURE*1
To do
Setting value
OFF, LOW, HIGH
Select the frequency of the luminance signal compensated in
“APERTURE LEVEL.”
APERTURE
Compensate the frequency response of the luminance signal of the
video signal.
01 – 10
LEVEL*1
sub menu
Display the sub menu which enables you to adjust the items of “PICTURE IMPROVEMENT” while
viewing the actual picture.
reset
Restore the default settings for all the items in “PICTURE IMPROVEMENT.”
• When the FOCUS lamp lights, “PICTURE IMPROVEMENT” does not appear on the menu (☞ r on page 6).
BACK LIGHT Setting value: –20 – +20
Adjusts the brightness of the display.
• When the DYNAMIC lamp lights, this item does not appear on the menu (☞ t on page 6).
Operation guide
Shows the buttons for
each operation.
Setting value: OFF, ON
COLOR RANGE MODE
Reduces the difference of the luminance level specific to the LCD panel.
• When “ON” is selected, the color temperature becomes the innate temperature in the LCD panel, and the
setting of “WHITE BALANCE SET.” becomes ineffective (☞ page 12).
VIDEO/COMPO. SEL.
Setting value: VIDEO, COMPO. (component)
Selects the signal type you want to use for the VIDEO/COMPONENT terminals.
• When select the component (COMPO.), make sure to set the component level in “COMPO. LEVEL” in
“PICTURE SUB ADJ.” (☞ page 12).
• The menu automatically disappears in about 30 seconds after the previous operation.
• Some items may not appear on the menu depending on the input or the input signal.
• The items controlled by the MAKE system do not appear on the menu.
ASPECT*1
Setting value: 4:3, 16:9
Changes the aspect ratio of the picture.
AREA MARKER*1
Setting for area marker functions
Item
To do
Setting value
☞ “NOTE”
4:3, 14:9, 13:9
OFF, 80% – 100%
☞ “NOTE”
MARKER SELECT*2
ASPECT SELECT*2
SAFETY MARKER
Select the style of the area marker.
Select the aspect ratio of the area marker.
Adjust the area of the safety marker.
R-MARKER SELECT*2 Select the style of the area marker.
R-ASPECT SELECT*2
R-SAFETY MARKER
Select the aspect ratio of the area marker.
Adjust the area of the safety marker.
4:3, 14:9, 13:9
OFF, 80% – 100%
• The area marker or the safety marker is displayed by using A. MARKER or S. MARKER button, or external
control.
NOTE
• Select either non-“R-” items or “R-” items to activate by using external control (☞ “External Control” on page
14).
• When a picture is displayed in 4:3 aspect ratio, the safety marker for the 4:3 area is displayed.
• To display the safety marker for the area of a picture displayed in 16:9 aspect ratio, hide the area marker.
Setting of “MARKER SELECT” and “R-MARKER SELECT”
The setting values and features are as follows.
OFF: “MARKER SELECT” and “R-MARKER SELECT” do not function.
LINE: Displays the area with an outline.
HALF: The area outside the specified aspect ratio of the screen is displayed as 50% transparency.
HALF+L: The area of the specified aspect ratio of the screen is indicated by an outline, and the area outside
of that is displayed as 50% transparency.
*1 Memorized for each input — composite signal input (VIDEO), component signal input (COMPO.), and SDI signal input.
*2 Displayed only when the picture is displayed in 16:9 aspect ratio.
BLK.: The area outside the specified aspect ratio of the screen is black. Only the portion of the picture within
the designated area is displayed.
BLK. +L: The area of the specified aspect ratio of the screen is indicated by an outline, and the area outside
of that becomes black so that only the area inside the line is displayed.
AUDIO SETTING
Setting for the audio channel group of the EMBEDDED AUDIO signals and level meter
Item
To do
Setting value
E.AUDIO GROUP
Select the audio channel group of the
EMBEDDED AUDIO signals.
☞ “NOTE”
BAR POSITION
LEVEL METER ch
CH ARRANGE
BAR TYPE
Select the type of the level meter display
— vertically or horizontally.
Select the number of the audio channels
displayed on the level meter.
Select the order of the audio channels
displayed on the level meter.
Select the color of the level meter display.
VERT. (vertically), HORZ. (horizontally)
OFF, 12CH, 8CH
LINE, DIVIDE (☞ “NOTE”)
3COLORS (3 colors to indicate variations in
input levels), W.100 (white), W.50 (half tone)
Operation guide
Shows the buttons for
each operation.
REFERENCE LEVEL Select the standard input level indicated on the –20dB, –18dB
level meter.
OVER LEVEL
Select the input level’s lower limit indicated in
red for the “3COLORS” display.
Select the brightness of the level meter.
–10dB, –8dB, –6dB, –4dB, –2dB
LOW, HIGH
• The menu automatically disappears in about 30 seconds after the previous operation.
• Some items may not appear on the menu depending on the input or the input signal.
• The items controlled by the MAKE system do not appear on the menu.
BAR BRIGHTNESS
SYNC FUNCTION
Setting for the monitor performance when no signal comes in
Item
To do
Setting value
NO SYNC ACTION
Select the screen status when no signal is
coming in.
OFF,
NOTE
P. SAVE (power save mode),
GRAY B. (gray screen)
Setting of “E.AUDIO GROUP”
The setting values and selectable audio channels of EMBEDDED AUDIO signals are as follows.
1G: channel(s) 1/2/3/4/1+2/3+4/1 – 4 (1G)
DELAY TIME
Select the period until the screen status
changes as selected in “NO SYNC ACTION”
after signals stop coming in.
30sec., 5min., 15min.
2G: channel(s) 5/6/7/8/5+6/7+8/5 – 8 (2G)
1-2G: channel(s) 1/2/3/4/5/6/7/8/1+2/3+4/5+6/7+8/1 – 4 (1G)/5 – 8 (2G)/1 – 8 (1G+2G)
3G: channel(s) 9/10/11/12/9+10/11+12/9 – 12 (3G)
1-3G: channel(s) 1/2/3/4/5/6/7/8/9/10/11/12/1+2/3+4/5+6/7+8/9+10/11+12/1 – 4 (1G)/5 – 8 (2G)/9 – 12
(3G)/1 – 8 (1G+2G)/1 – 12 (1-3G)
• Setting “NO SYNC ACTION” to “GRAY B.” saves the power consumption of the back light by half. (The screen
color changes to gray.)
Selecting “P.SAVE” saves more power consumption by turning off the back light.
Example of the level meter display—Level meter position and audio channels
Ex.: When “LEVEL METER ch” is set to “8CH” and “BAR TYPE” is set to “3COLORS.”
REFERENCE LEVEL
OVER LEVEL
REFERENCE LEVEL
OVER LEVEL
• When “CH ARRANGE” is set
to “DIVIDE,” a odd channel is
displayed on the left and an
even channel is displayed on the
right.
Green
Green
Red
Red
Yellow
Yellow
• When “BAR TYPE” is set
to “W.100” or “W.50,” the
standard input level set in
the “REFERENCE LEVEL” is
displayed with the line indication.
The input level set in “OVER
LEVEL” is not displayed.
• The level meter with no signal
input is displayed in white for
“3COLORS,” and in gray for
“W.100” or “W.50.”
Ex.: BAR POSITION: HORZ.,
CH ARRANGE: LINE
Ex.: BAR POSITION: HORZ.,
CH ARRANGE: DIVIDE
OVER LEVEL
OVER LEVEL
Red
Yellow
Green
Red
Yellow
Green
REFERENCE LEVEL
REFERENCE LEVEL
Ex.: BAR POSITION: VERT.,
CH ARRANGE: LINE
Ex.: BAR POSITION: VERT.,
CH ARRANGE: DIVIDE
ENGLISH
11
12
Menu Configuration—SET-UP MENU
For the operation procedure, see page 7.
FUNCTION SETTING
Setting for the sub menu display, color system, color of the tally lamp, and format indicator
Item
To do
Setting value
sub menu POSI.
COLOR SYSTEM
Select the contents and displaying position of “sub menu.”
Select the color system.
• If the picture is unstable with “AUTO,” select “NTSC” or “PAL.”
☞ “NOTE”
AUTO, NTSC, PAL
TALLY SELECT
Select the color of the tally lamp.
GREEN, RED
FORMAT INDICATOR Select whether to use the tally lamp as the format indicator.
OFF, ON (☞ “NOTE”)
• When “FORMAT INDICATOR” is set to “ON,” the TALLY function of the MAKE/TRIGGER terminal is not
available.
PICTURE SUB ADJ.
Adjusts the standard level for the picture adjustment and selects the set-up level for the input video signal.
Item
CONTRAST*1
To do
Setting value
–20 – +20
Operation guide
Shows the buttons for
each operation.
Adjust the standard level for the contrast adjusted with
CONTRAST knob on the front panel.
BRIGHT*1
CHROMA*1
PHASE
Adjust the standard level for the brightness adjusted
with BRIGHT knob on the front panel.
Adjust the standard level for the chroma adjusted with
CHROMA knob on the front panel.
Adjust the standard level for the phase adjusted with
PHASE knob on the front panel.
–20 – +20
–20 – +20
–20 – +20
NTSC SETUP
Select the set-up level of the input NTSC signal.
00 (compliant with 0% set-up signal), 7.5
(compliant with 7.5% set-up signal)
COMPO. LEVEL Select the level of the analog component signal (480i
SMPTE (compliant with M2VTR signals),
B75 (compliant with BetacamVTR 7.5%
set-up signal), B00 (compliant with
BetacamVTR 0% set-up signal)
and 576i only).
• The menu automatically disappears in about 30 seconds after the
previous operation.
• Some items may not appear on the menu depending on the input or
the input signal.
• The items controlled by the MAKE system do not appear on the menu.
sub menu
reset
Display the sub menu which enables you to adjust the items in “PICTURE SUB ADJ.” while viewing
the actual picture.
Restore the default settings for all the items in “PICTURE SUB ADJ.”
• When the DYNAMIC lamp lights, “PICTURE SUB ADJ.” does not appear on the menu (☞ t on page 6).
H. POSITION*2
Setting value: –003 – +003
NOTE
Adjusts the horizontal picture position.
Setting of “sub menu POSI.”
WHITE BALANCE SET.
Selects the color temperature and adjusts the drive level of each color (R/G/B).
Item
COLOR TEMP.
R DRIVE, G DRIVE,
B DRIVE*3
sub menu
The setting values and features are as follows.
LOWER1: Displays the current setting and adjustment bar at the lower part of the screen.
UPPER1: Displays the current setting and adjustment bar at the upper part of the screen.
LOWER2: Displays the current setting at the lower part of the screen.
UPPER2: Displays the current setting at the upper part of the screen.
To do
Setting value
6500K, USER, 9300K
Select the color temperature.
Adjust the drive level of each color (red, green, and blue). –128 – 000 – MAX
• The adjustment bar is not displayed for some items.
Display the sub menu which enables you to adjust the items in “WHITE BALANCE SET.” while
viewing the actual picture.
Restore the default settings for the drive levels of the selected color temperature.
Color of the format indicator
When “FORMAT INDICATOR” is set to “ON,” the tally lamp lights as follows according to the incoming video
signal.
Lights in green: 720/60p, 720/59.94p, 720/50p, 1080/60i, 1080/59.94i, 1080/50i, 1035/60i, 1035/59.94i,
1080/24psF, 1080/23.97psF, 1080/30psF, 1080/25psF, 1080/29.97psF
Lights in red: 480/59.94i, 576/50i, 480/59.94p, 576/50p
Lights in orange: composite signal
reset
• When “COLOR RANGE MODE” is set to “ON,” “WHITE BALANCE SET.” does not appear on the menu (☞ page
10).
*1 Memorized for each input — composite signal input (VIDEO), component signal input (COMPO.), and SDI signal input.
*2 Memorized for each signal format.
*3 Memorized for each color temperature.
• The lamp goes off when the non-compliant video signals are coming in.
(☞ “External Control” on pages 14 and 15)
REMOTE SETTING
Setting for the external control
Item
To do
Setting value
TYPE SEL.
Select the external control method for the MAKE, TRIGGER, SET
MAKE/TRIGGER terminal.
PIN1, PIN2, PIN3,
PIN4, PIN5
Assign the control functions to the pins of COLOR OFF, SCR CHECK, A.MARKER,
the MAKE/TRIGGER terminal.
S.MARKER, FOCUS, DYNAMIC, SDI, VIDEO/
COMPO., ASPECT, TALLY SEL, SOURCE ID,
MUTING, MARK.SEL, L.METER, STATUS, COLOR
• Assign a function to each pin terminal
by selecting “SET” in “TYPE SEL.”
(The functions are assigned for “PIN6” RANGE, – – – (no function)
– “PIN8” and you cannot change the
assignment of these functions.)
Operation guide
Shows the buttons for
each operation.
INFORMATION
Setting for the information display of the monitor
Item
SOURCE ID
To do
Setting value
OFF, ON
Select if the name assigned in “CHARACTER SET.” is displayed on
the screen (☞ “About the Information Display” on page 7).
CHARACTER SET.
STATUS DISPLAY
Assign a name to each video source as you like (10 characters at
maximum).You can also enter a name using the RS-232C system.
Select if the status of the current input and setting of muting are
☞ “NOTE”
AUTO, OFF, ON
displayed on the screen (☞ “About the Status Display” on page 7).
SUB HOUR METER Display the hours of use (unit: hour).You can reset this item.
MODEL
VERSION
HOUR METER
Display the model name of the monitor.
Display the version of the monitor.
Display the total hours of use (unit: hour). This item is used for the maintenance of the monitor.
You cannot reset this item.
• The menu automatically disappears in about 30 seconds after the previous operation.
• Some items may not appear on the menu depending on the input or the input signal.
• The items controlled by the MAKE system do not appear on the menu.
CONTROL LOCK
Setting value: OFF, ON
Turns on (or off) the control lock function to disable the buttons on the front panel.
• The following operations are available even when this function is activated.
– Turning on/off (on standby) the monitor
– Displaying the SET-UP MENU (by pressing button while pressing button) and turning “CONTROL LOCK”
to “OFF”
– Operating the monitor by an external control
If you try other operations, “ Control lock on!” appears on the screen.
all reset
NOTE
Restores all the settings and adjustments of the monitor to the default.
• “HOUR METER” and the settings done by using the adjustment knobs on the front panel will not be reset.
• When you operate the monitor with the AC power supply, the monitor is turned off (on standby) then turned
on automatically. When you operate the monitor with the DC 12 V power supply, the monitor is turned off (on
standby).
Setting of “CHARACTER SET.”
Assign a name for each video source following the steps below.
1 Change the input to one that you want to assign a video source name for (VIDEO/COMPO. or SDI).
• You cannot store different video source names for composite signal input (VIDEO) and component
signal input (COMPO.).
2 Select “CHARACTER SET.”
3 Press
buttons to select the first character.
• Each time you press button, the character changes as follows. Press button to reverse the order.
Space
4 Press button to move the arrow to the next.
• The characters entered before moving the arrow are memorized.
5 Repeat steps 3 and 4 (10 characters at maximum).
6 Press MENU button to store the name.
ENGLISH
13
14
External Control
To assign the functions to the pin terminals
For the operation procedure, see page 7.
1 Select “REMOTE SETTING” on the SET-UP MENU.
2 Set “TYPE SEL.” to “SET.”
7 About the external control
This monitor has two external control terminals.
• MAKE/TRIGGER terminal (RJ-45): The following external control systems are available.
(1) MAKE (make contact) system: Controls the monitor by short-circuiting the corresponding pin terminal to
the GND pin terminal, or disconnecting (opening) it (☞ below).
(2) TRIGGER (trigger) system: Controls the monitor by sending the pulse signal instantaneously to the
corresponding pin terminal (☞ below).
3 Select a pin name (“PIN1” – “PIN5”) for which you want to assign a function, then select the function you want
to assign.
• For selectable functions, see the tables below.
Functions controlled by the MAKE/TRIGGER system
• RS-232C terminal (D-sub 9-pin): Controls the monitor with the RS-232C system. (☞ page 15)
Functions to be
controlled
Color off
Short-
circuiting
Monochrome
Functions to be
controlled
ASPECT Changes the aspect
ratio.
Short-
circuiting
16:9
Display
Opening
Display
Opening
• Control priority is as follows.
COLOR
OFF
Color
4:3
MAKE > TRIGGER, RS-232C, buttons and menu on the monitor
• You can use the external control even when “CONTROL LOCK” is set to “ON” (☞ page 13).
• When the monitor is off (on standby), external control is not available.
SCR
CHECK
Screens check
TALLY
SEL
SOURCE
ID
Selects the color of the Green
tally lamp.
☞ “SOURCE ID” on
page 13
Red
On
4
*
A.MARKER The area marker
Off
On
On
On
On
Off
display
7 Using the MAKE/TRIGGER system
S.MARKER The safety marker Off
display
MUTING Muting on/off
Off
On
You can control the monitor by a personal computer or dedicated controller*1.
MARK.
SEL
Selects the items of
Non-“R-” ”R-” items
items
*1 The controller is not commercially available. Consult your dealer if you need it.
FOCUS
Helps to focus the Off
picture.
“AREA MARKER”*5
L.METER Audio level meter
display
STATUS Status display*7
6
DYNAMIC Adjusts the picture Off
to be suitable for the
*
The MAKE/TRIGGER terminal is configured as follows.You can assign a function to each pin terminal in
“REMOTE SETTING” (☞ “PIN1, PIN2, PIN3, PIN4, PIN5” on page 13).
☞ “About the Status
Display” on page 7
light place.
Changes the input Invalid
to “SDI.”
Changes the input Invalid
to “VIDEO/COMPO.”
SDI
Valid
Valid
Pin No.
Pin name
PIN1
PIN2
PIN3
PIN4
Pin No.
Pin name
PIN5
PIN6 (TALLY)*2
PIN7 (ENABLE)*3
PIN8 (GND)
COLOR Reduces the difference
RANGE of the luminance level
specific to the LCD
panel.
— — — No function
This is a female
terminal.
1
2
3
4
5
6
7
8
VIDEO/
COMPO.
Off
—
On
—
*2 The 6th pin terminal controls turning on or off the tally lamp (available to control even when the 7th pin terminal is
invalid.)
*3 The 7th pin terminal makes the external control valid/invalid. Make sure to control the terminal by the MAKE system.
*4 While controlling with the MAKE system, the screen is switched between normal screen (opening) and blue screen
(short-circuiting). While controlling with the TRIGGER system, the screen changes as follows.
Normal screen
Red screen
• You cannot change the functions assigned to the pin terminals from 6th to 8th.
• When “FORMAT INDICATOR” in “FUNCTION SETTING” is set to “ON,” the TALLY lamp cannot be controlled by
the external control (☞ page 12)
Blue screen
Green screen
*5 Selects which functions in “AREA MARKER” are activated, non-“R-” items or “R-” items (☞ page 10).
*6 While controlling with the MAKE system, the level meter is switched between displayed (short-circuiting) and hidden
(opening). When “LEVEL METER ch” is set to “OFF,” the level meter is not displayed (“NO EFFECT” appears). While
controlling with the TRIGGER system, the number of the audio channels displayed is changed (between OFF, 12CH
and 8CH).
*7 Displays the information shown when the button of the current input is pressed (☞ “About the Status Display” on page
7). While controlling with the MAKE system, the information is displayed only at the moment of short-circuiting.
• You cannot assign the same function to different pin terminals.
• The TRIGGER system switches each function by short-circuiting the pin terminal for about 1 second and
opening it.
Operation
<Basic command list>
1 Set “TYPE SEL.” of “REMOTE SETTING” to “MAKE” or “TRIGGER” in the SET-UP MENU.
2 Short-circuit the 7th pin terminal (ENABLE) to the 8th pin terminal (GND) so that the monitor can be controlled
by the external control.
No.
1
2
Commands
Functions
Starts communication (connection)
Terminates communication (termination)
Displays the MAIN MENU/Quits the menu
operation
Data
No data
No data
!
!
0
0
0
0
B
B
C
C
N
N
1
0
Cr
Cr
3 When selecting “MAKE” system: Operate each function by short-circuiting the corresponding pin terminal to
3
!
0
0
B
M E
N
U
Cr
No data
the 8th pin terminal (GND) or opening it.
When selecting “TRIGGER” system: Operate each function by pulse control, that is short-circuiting the
corresponding pin terminal to the 8th pin terminal (GND) for about 1 second and opening it.
4
5
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
U
D
A
A
S
P
P
I
P
O
D
D
E
Cr
No data
Moves the cursor upward (
)
W N Cr
No data
Moves the cursor downward (
)
6
7
8
9
10
11
12
13
14
15
16
17
18
J
J
T
R
L
U
Cr
Cr
P
Makes setting/adjustment (
Makes setting/adjustment (
Displays the SET-UP MENU
Turns on the monitor
)
)
No data
No data
No data
No data
No data
No data
No data
No data
No data
No data
00 – 30
00: Off, 01: On
00: 4:3, 01: 16:9
• When changing the input with MAKE system, only one pin terminal must be short-circuited. (Other pin terminals
must be opened.)
• When selecting the “TRIGGER” system, you can operate only one function at a time. Operate the functions one
by one.
Cr
W 1 Cr
W 0 Cr
Turns off the monitor (standby)
Selects “SDI” input
Selects “VIDEO/COMPO.” input
Displays the status*2
Increases the volume level
Decrease the volume level
Adjusts the volume level
Turns muting on/off
7 Using the RS-232C system
N
N
I
P
M N
A
B
S
L
Cr
Cr
P
S
S
x
I
You can control the monitor from a personal computer etc. via the RS-232C terminal.
• Consult your dealer for the details of the external control specification.
D
V
V
V
A
A
Cr
Cr
Cr
<Communication specifications>
Baud Rate: 4800 bps
Data Bits: 8 bits
Parity: No parity
Stop Bits: 1 bit
Flow Control: No control
O
L
x*1 Cr
M U
T
x
E
x
x*1 Cr
S
P
x*1 Cr
Changes the aspect ratio
• “Cr” is 0Dh.
• The commands for starting communication (connection) (No. 1), terminating communication (termination)
(No. 2), and turning on the monitor (No. 9) can be used while the monitor is off (on standby).
Communication Code: ASCII Code
• Use a straight cable with a D-sub 9-pin connector (male for the monitor, female for the personal computer).
*1 Enter the appropriate data to “xx”.
<Command outline>
All commands consist of the following segments.
*2 Displays the information shown when the button of the current input is pressed (☞ “About the Status Display” on page
7).
Header
Monitor ID (00)
Command ID
Function
Data
Cr (0DH)
<Specifications of the RS-232C terminal>
Header
“!”: Operation commands from the personal computer, etc. For details, see <Basic command list> on the right.
“?”: Reference commands from the personal computer, etc.
“@”: Status returns from the monitor
Pin No.
Signal
NC
1
2
3
4
5
6
7
8
9
RXD
TXD
NC
• To start communication, send the connection command from the personal computer etc.
• To terminate the communication, send the termination command from the personal computer etc.
This is a female
terminal.
GND
NC
Example of communication procedures
RTS
CTS
NC
1 Starting the communication: connection command
(!00BCN1Cr)
2 Monitor’s status (@00BOKCr)
Monitor
• The 7th terminal and the 8th terminal are connected.
3 Selecting “SDI” input (!00BINACr)
4 Monitor’s status (@00BOKCr)
PC, etc.
5 Terminating the communication: termination command
(!00BCN0Cr)
6 Monitor’s status (@00BOKCr)
ENGLISH
15
16
Troubleshooting
The following are not malfunctions.
Solutions to common problems related to the monitor are described here. If none of the solutions presented here
solves the problem, unplug the monitor and consult an authorized dealer or service center.
• When a still image is displayed for a long time, it may remain indistinctly on the screen after the picture has
changed. Though the remaining picture will disappear after a while, there may be a case that it remains
for a long period depending on the length of time the still image was displayed for. This is due to the
characteristics of the LCD display and is not a malfunction.
• The red spots, blue spots and green spots on the panel surface are a normal characteristic of LCD displays,
and not a problem. The LCD display is built with very high precision technology; however, be aware that a
few pixels may be missing or constantly lit.
Symptom
Probable cause and corrective action
Page
• Turn on the POWER switch or DC switch on the rear panel.
• Firmly insert the AC power plug or DC 12 V power plug.
• When using the DC 12 V power supply, charge the battery or
replace it with the one charged.
8
8
8
No power supply
• The following symptoms are problems only when pictures or sounds are not played back normally.
– A slight electric shock occurs when you touch the monitor.
– The top and/or rear panel of the monitor becomes hot.
– The monitor emits a cracking noise.
– The monitor emits a mechanical noise.
• Select the correct input.
• Connect the signal cable firmly.
• Turn on the power of the connected component and set the
output correctly.
• Check if the input signal format is acceptable on the monitor.
6
8
—
No picture with the power on
9
• Adjust the volume level.
6
6
8
• Deactivate the muting function.
• Connect the signal cable firmly.
• Turn on the power of the connected component and set the
output correctly.
No sound
7 Self-check program
—
This monitor has a self-check function, which allows it to detect malfunctions and alert you. This makes
troubleshooting easier. Whenever a problem occurs, one or some of the self-check lamps will flash. If this
happens, follow the steps below and contact your dealer to resolve the problem.
“OTHERS” or “Out of range”
appears.
• Check if the input signal format is acceptable on the monitor.
7, 9
• Select the correct input.
• Connect the signal cable firmly.
6
8
Self-check lamps
“NO SYNC” appears.
• Turn on the power of the connected component and output
video signals. Or, check if the video output of the component
(video output setting of the VCR, etc.) is set correctly.
—
• Adjust the each picture adjustment knob on the front panel
or adjust the items of “PICTURE SUB ADJ.” in the SET-UP
MENU. Or, perform “reset” in “PICTURE SUB ADJ.”
• Check if the screen mode is other than normal screen, by
using SCR. CHK. button.
6, 12
6
Wrong color, no color
• Select the proper color system (“COLOR SYSTEM”) in
“FUNCTION SETTING” of the SET-UP MENU.
• Adjust the items of “WHITE BALANCE SET.” in the SET-UP
MENU. Or, perform “reset” in “WHITE BALANCE SET.”
12
12
• Adjust the picture contrast or brightness by using the
adjustment knobs on the front panel. Or, adjust “CONTRAST”
or “BRIGHT” of “PICTURE SUB ADJ.” in the SET-UP MENU.
6, 12
The picture becomes blurred.
When the screen goes blank and check one or some self-check lamps on the front control panel start
flashing...
• Check if the input signal format is acceptable on the monitor.
• Check the setting of “ASPECT” in the MAIN MENU.
• Adjust the horizontal picture position in “H. POSITION” of the
SET-UP MENU.
• For some signals, the picture cannot be displayed fully in the
effective screen area. There is no sure method to solve this
problem.
9
10
12
1 Check which lamps are flashing.
2 Turn off the POWER switch or DC switch on the rear panel.
3 When AC power supply is used, disconnect the AC power cord from the AC outlet.
When DC 12 V power supply is used, detach the battery or disconnect the plug
from the DC IN 12V terminal.
Wrong picture position, wrong
picture size.
—
• The items which are not available for the current input or the
current input signal are not displayed on the menu. Change
the input or the input signal.
• The items controlled by the MAKE system do not appear on
the menu.
—
Some items do not appear on
the menu.
14
13
4 Contact your dealer with the information about which lamps are flashing.
• If you turn on the monitor soon after turning it off (or after a short-term power failure), the self-check lamps may
flash and no image may be displayed. When this happens, turn off power and wait at least 10 seconds before
turning on the monitor again. If the self-check lamps do not flash, you can use the monitor as normal.
Buttons on the monitor do not
work.
• Set “CONTROL LOCK” in the SET-UP MENU to “OFF.”
Specifications
7 General
7 Input/output terminals
Model name
Type
DT-V9L1D
VBS/Y
Composite signal/analog component (Y) signal input/output:
1 line, BNC connector x 2
1 V(p-p), 75 Ω
Multi format LCD monitor
Type 9 wide format
15:9
Screen size
Aspect ratio
LCD panel
* The input (IN) and output (OUT)
terminals are bridge-connected (auto
termination)
VIDEO/COMPONENT
(IN/OUT)
9˝ wide, IPS-Pro
Width: 195 mm
Height: 117 mm
Effective screen size
PB, PR
Analog component (PB, PR) signal input:
1 line, BNC connector x 2
0.7 V(p-p), 75 Ω
Number of pixels displayed
Number of colors displayed
Viewing angle (TYP.)
800 x 480
16.20 million
170° (Horizontally), 170° (Vertically)
Digital signal input (compatible with EMBEDDED AUDIO signals):
auto detection, 1 line, BNC connector x 1
E. AUDIO HD/SD SDI (IN)
E. AUDIO HD/SD SDI (OUT)
Panel brightness (at least)
(TYP.)
350 cd/m2
Digital signal output (compatible with EMBEDDED AUDIO signals):
1 line, BNC connector x 1
Contrast ratio (TYP.)
400:1
Analog audio signal input/output:
1 line, RCA connector x 2,
500 mV (rms), high impedance
* The input (IN) and output (OUT)
terminals are bridge-connected (auto
termination)
Compliant video signal format
☞ “Available signals” on page 9
HD SDI: BTA S-004B, SMPTE292M
SD SDI: ITU-R BT.656: 525/625
SMPTE259M: 525
AUDIO (IN/OUT)
Format
EMBEDDED AUDIO: SMPTE299M, SMPTE272M
Audio output
Internal speaker: 1.0 W
REMOTE (MAKE/TRIGGER)
REMOTE (RS-232C)
Operating temperature: 0°C – 40°C
Operating humidity: 20 % – 80 % (non-condensing)
* Slightly variable depending on ambient conditions for installation.
☞ “Using the MAKE/TRIGGER system” on page 14
☞ “Using the RS-232C system” on page 15
Operating conditions
AC 120 V/AC 220 – 240 V, 50 Hz/60 Hz
DC 12 – 17 V
Power requirements
Rated current
0.35 A (AC 120 V)/0.25 A (AC 220 – 240 V)
1.7 A (DC 12 – 17 V)
Width:
222.4 mm
Height: 218 mm (at the higher position), 181 mm (at the lower position),
176 mm (without stand)
External dimensions
(excluding protruding parts)
Depth:
185 mm (at the higher position), 202 mm (at the lower position),
116 mm (without stand)
3.6 kg (with the stand)
2.7 kg (without the stand)
Weight
AC power cord x 2, Power cord holder x 1, Screw x 2 (for power cord holder),
Protective filter x 1, Screw (for protective filter) x 4
Accessories
• For easy understanding, pictures and illustrations are shown by being emphasized, omitted or composed,
and may be slightly different from actual products.
• Design and specifications are subject to change without notice.
• All company names and product names mentioned herein are used for identification purposes only, and may
be the trademarks or registered trademarks of their respective companies.
Use the Anton Bauer Dionic 90 (mount: QR DXC-M3A) external battery.
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
Notice on transportation
This monitor is precision equipment and needs dedicated packing material for transportation.
Never use any packing material supplied from sources other than JVC or JVC-authorized dealers.
ENGLISH
17
18
Specifications (cont.)
Unit: mm
7 Dimensions
<Front view>
<Side view>
<Rear view>
• When the stand is attached to the
higher position.
• When the stand is attached to the
lower position.
116
VESA mounting holes
(8-M4, depth: 10 mm)
100
75
27.5
1.5
222.4
202
13
186
185
* at the higher position
** at the lower position
tapped hole (3/8˝)
tapped hole (1/4˝)
|